E120S Write dump 512 = ATF OK | Cộng Đồng GSM Việt Nam-Đồng Hành-Hỗ trợ-Thành Công

Trùm vật tư ép kính | Bệnh Viện Điện Thoại 24h | Linh Kiện Tín Thành | Đặt chữ quảng cáo | Đặt chữ quảng cáo | Trùm điện thoại cổ độc

E120S Write dump 512 = ATF OK

Thảo luận trong 'Samsung' bắt đầu bởi ĐiệpNhànMobile, 22/1/15.

  1. ĐiệpNhànMobile

    • VIP
    Gia đình Vietnamgsm
    Làm thành viên từ: 31/7/13
    Bài viết: 475
    Cảm ơn: 333
    Điểm: 70
    M:
    Vietnamgsm GOLD:
    Bạn không thể xem nội dung này - Vui lòng đăng ký thành viên để được xem ! Cảm ơn. Write dump 512 = ATF OK



    1. DO NOT USE THE PHONE"S BATTERY
    2. Connect the Soldered TP Connections to ATF Box
    3. Disconnect the USB Cable and Wait until the
    the ATF Software will tell you to Connect the USB.


    Interface Reset OK!
    eMMC Access Type: SECTOR MODE
    eMMC Supported Voltage Range:
    3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
    3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

    CID : 1501004B594C30304D12617B66E0
    CSD : D02701320F5903FFF6DBFFEF8A404067

    eMMC Boot Information
    Revision 1.5 (for MMC v4.41)
    BOOT PARTITION : NOT BOOT ENABLED
    PARTITION ACCESS : R/W USER PARTITION
    PERM_BOOT_CFG_PROT : DISABLED
    PWR_BOOT_CFG_PROT : DISABLED
    BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
    RESET BUS WIDTH : ENABLED
    eMMC FirmW UPDATE : DISABLED
    EMMC CACHE SIZE : 0 KB
    SUPER PAGE SIZE : 3584 KB
    HC ERASE GROUP SIZE: 512 KB
    USER AREA SIZE : 15758000128 BYTES
    BOOT PARTITION SIZE: 512 KB
    RPMB PARTITION SIZE: 128 KB


    eMMC Device Information
    Manufacturer ID: SAMSUNG
    Device Type : Embedded BGA
    Application ID : 00
    Product Name : KYL00M
    Product Rev : 1.2
    Product SN : 617B66E0
    Manufactured : January 2011

    Card Specific Data
    CSD_STRUCTURE : Extended
    SPEC_VERS : Version 4.1/4.2/4.3
    TAAC : 13 ns
    TRANS_SPEED : 4000000 KHz
    READ_BL_LEN : 512 Bytes
    C_SIZE : HIGH CAPACITY
    WP_GRP_ENABLE : YES
    WRITE_BL_LEN : 512 Bytes
    CONTENT_PROT_APP : NO
    PERM_WRITE_PROTECT: NO
    TMP_WRITE_PROTECT : NO

    Extended CSD Saved:
    1501004B594C30304D12617B66E0_6F8B52EC.ext_csd
    Backup Directory:
    C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\


    Task Selected: Normal Factory Erase
    ======================================================
    For eMMC Revision 1.2 (for MMC v4.2) and LOWER
    --> This will ERASE USER AREA, BOOT1, BOOT2, and RPMB
    For eMMC Revision 1.3 (for MMC v4.3) and HIGHER
    --> This will ONLY ERASE USER AREA
    ======================================================
    This eMMC is: Revision 1.5 (for MMC v4.41)

    Factory Erasing Supported FLASH AREA...
    Normal Factory Erase Done!

    ======================================================
    WARNING - WARNING - WARNING - WARNING - WARNING
    ======================================================
    1. WRITE BOOT1 Image if Needed
    2. WRITE BOOT2 Image if Needed
    3. WRITE USER AREA Image if Needed
    ======================================================
    Start Writing 0x00100000 Blocks at 0x00000000
    Partition Selected: USER AREA

    Total Elapsed Time 00:14:23
    Write Success!
     

    ****************Để giúp forum phát triển,anh em vui lòng share Facebook, Google+ ****************
    t2hgsm and joneskiller2008 đã cảm ơn bài viết này.

Thành viên đang xem bài viết này (Thành viên: 0, Khách: 0)

X

Hỗ trợ kỹ thuât >> CHAT ngay !