Nokia Lumia 520 Repair Boot Không Tháo Máy Ok | Cộng Đồng GSM Việt Nam-Đồng Hành-Hỗ trợ-Thành Công

Trùm vật tư ép kính | Bệnh Viện Điện Thoại 24h | Linh Kiện Tín Thành | Đặt chữ quảng cáo | Đặt chữ quảng cáo | Trùm điện thoại cổ độc

Nokia Lumia 520 Repair Boot Không Tháo Máy Ok

Thảo luận trong 'Nokia' bắt đầu bởi ChiTruongSW, 5/2/16.

  1. ChiTruongSW

    • Moderator
    Chuyên viên kỹ thuật dự bị
    Làm thành viên từ: 23/7/13
    Bài viết: 519
    Cảm ơn: 161
    Điểm: 599
    Nghề nghiệp: Phần Mềm Di Động
    M:
    Vietnamgsm GOLD:
    Nokia Lumia 520 Repair Boot Không Tháo Máy Ok

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]

    Mã:
    Windows Phone 8/8.1/10 Flashing Started
    Loading Flash Files Please Wait...
    
    [DEAD BOOT REPAIR via USB is SUPPORTED]
                                                         
    ======================================================
             Windows Phone 8/8.1/10 Lumia Flasher          
    ======================================================
                                                         
    If the Phone is ALIVE                                
      1. Power On the Phone and Connect it to the USB Port
                                                         
    If the Phone is DEAD                                 
      1. Connect Phone to the USB Port                   
      2. Press and Hold the VOLUME DOWN and POWER Buttons
      3. Wait until the Phone Vibrates Shortly...        
      4. Stop Pressing the Buttons...                    
                                                         
    If the Phone is DEAD BOOT                            
      1. Connect Phone to the USB Port                   
      2. Install Correct Drivers:                        
         "Nokia Emergency Connectivity" Located at:      
                                                         
    C:\AdvanceBox Turbo Flasher\Driver\NOKIA_X2_USB_DRIVERS\
    ======================================================
                                                         
    Recovery Handle Found! - (Qualcomm)
    Sending Factory Loader...
    Loader Upload Done!
    Executing Loader...
    Start Loader Done!
    Waiting for USB Cycle...
    USB Cycle OK!
    Device Factory Mode OK!
    USB Reconfiguration Done...
    eMMC Detected OK...
    
    Extracting Partitions from FFU...
    Looking for SBL1...
    SBL1 OK
    Looking for SBL2...
    SBL2 OK
    Looking for SBL3...
    SBL3 OK
    Looking for UEFI...
    UEFI OK
    Looking for RPM...
    RPM OK
    Looking for TZ...
    TZ OK
    Looking for WINSECAPP...
    WINSECAPP OK
    Extracting Partitions Done!
    Start Writing eMMC Blocks at : 0x00000000
    Start Writing eMMC Blocks at : 0x01000000
    Start Writing eMMC Blocks at : 0x01200000
    Start Writing eMMC Blocks at : 0x01400000
    Start Writing eMMC Blocks at : 0x01600000
    Start Writing eMMC Blocks at : 0x01A00000
    Start Writing eMMC Blocks at : 0x01C00000
    Start Writing eMMC Blocks at : 0x01E00000
    eMMC Write OK!
    Closing Partition...
    Partition Close OK!
    BOOT WRITE DONE!
    Waiting for USB Cycle...
    USB Cycle OK!
    Rebooting Phone...
    Nokia Phone Info Mode Initiated...
    Please wait upto 15 Seconds for SW Reset
    Version: 1.1.1.3
    Product Code: 059S357
    Module Code: 0205435
    
    Continuing Previous Boot...
    Please wait upto 30 Seconds for Boot Re-entry
    
    Boot Flash Mode Successful...
    Buffers Flushed OK...
    
    Phone Info Query Start...
    Blocks Returned: 0x07 Blocks
    Block ID 0x01 : 00241000
    Block ID 0x02 : 00240000
    Block ID 0x03 : 00E90000
    Block ID 0x05 : Nokia.MSM8227.P6036.1.2
    Block ID 0x0D : 0001
    Block ID 0x0F : 0301010100000101FF
    Block ID 0x10 : 0100130000
    Checking SD Card Size...
    Card Size: 0x00000000
    Checking Platform Security Status...
    Platform Secure Boot Status: Active
    Secure FFU EFUSE Status: Active
    Debug Status: Active
    RDC Status: Not Active
    Authentication Status: Not Active
    UEFI Secure Boot Status: Active
    Checking Secure FFU Mode...
    Secure FFU Mode :
    Query Flash App Information...
    Flash App Information: 02010F011C00
    UEFI App: FLASH APP
    Flash App Protocol Version: 1.15
    Flash App Implementation Version: 1.28
    Query ROOT KEY HASH...
    ROOT_KEY_HASH: F771E62AF89994064F77CD3BC16829503BDF9A3D506D3FACECAEF3F808C868FD
    Query PUBLIC ID...
    PUBLIC_ID: D6757E808E8623AE4FAA3E63B836602FBC61EF79
    Query eMMC Info...
    EMMC Manufacture ID: SAMSUNG
    EMMC Product SN : E71B81B8
    EMMC_SIZE: 8 Gigabytes
    Query Battery Charge Status...
    CHARGING_STATUS: Cannot Read in Flash Mode
    
    Sending Image Signatures...
    Image Signatures Accepted!
    Erasing Data Partition...
    Data Partition Erased Successfully
    Preparing Buffers for DATA LOOP...
    Allocating System RAM OK!
    Start Sending DATA BLOCKS...
    Finished Sending all DATA BLOCKS!
    Exiting FLASH Mode via REBOOT...
    Exit FLASH Mode Successful!
    
    Flashing Done!
    Total Flashing Time : 00:01:38
    
     

    ****************Để giúp forum phát triển,anh em vui lòng share Facebook, Google+ ****************

Thành viên đang xem bài viết này (Thành viên: 0, Khách: 0)

X

Hỗ trợ kỹ thuât >> CHAT ngay !