Repair boot LG F100s ok | Cộng Đồng GSM Việt Nam-Đồng Hành-Hỗ trợ-Thành Công

Trùm vật tư ép kính | Bệnh Viện Điện Thoại 24h | Linh Kiện Tín Thành | Đặt chữ quảng cáo | Đặt chữ quảng cáo | Trùm điện thoại cổ độc

Repair boot LG F100s ok

Thảo luận trong 'RIFF-JTAG' bắt đầu bởi truyengsm, 12/6/14.

  1. truyengsm

    • Admin Vietnamgsm
    Product Manager
    Làm thành viên từ: 27/6/13
    Bài viết: 3,103
    Cảm ơn: 4,471
    Điểm: 10,375
    Nghề nghiệp: Unlock - Repair boot - Nạp Tiếng Việt all Mobile
    Nơi ở: 739 Đường 3/2 F6 Q10 TPHCM
    M:
    Vietnamgsm GOLD:
    6-12-2014 8-26-32 AM.jpg 6-12-2014 9-44-54 AM.png
    Mã:
    Welcome to Octoplus/Octopus Box LG Software version 1.5.6
    Searching Diagnostic Ports...OK
    --------------------------------------------------------------------------------
    Platform: LG Qualcomm
    Selected port: COM24
    Selected model: F100S
    Reading info...OK
    Mode: Emergency
    Model ID: 8660-AAABQNBYA-34701
    SW version: IPROJECT
    IMEI: 000000-00-000000-0
    Opening "LGF100SAT-00-V40d-450-05-JUN-11-2013+0.oct"...OK
    Initializing flash...OK
    Formating USERDATA...OK
    Formating GROW...OK
    Writing MODEM...OK
    Writing SBL1...OK
    Writing SBL2...OK
    Writing EXT...OK
    Writing RPM...OK
    Writing SBL3...OK
    Writing ABOOT...OK
    Writing BOOT...OK
    Writing TZ...OK
    Writing PERSIST...OK
    Writing RECOVERY...OK
    Writing MDM...OK
    Writing TOMBSTONES...OK
    Writing SYSTEM...OK
    Writing GROW...OK
    Finalizing...OK
    Writing firmware done!
    
    Mã:
    Open serial port...OK
    Connecting to the RIFF Box...OK
    Firmware Version: 1.37, JTAG Manager Version: 1.55
    Selected Resurrector: [LG F100S V1.0.5032.43631]
    
    Connecting to the dead body...OK
    Detected dead body ID: 0x106A10E1 - CORRECT!
    Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
    Adaptive Clocking RTCK Sampling is: [Sample at MAX]
    
    Resurrection sequence started.
    Establish communication with the phone...OK
    Initializing internal hardware configuration...OK
    Uploading resurrector data into memory...OK
    Starting communication with resurrector...OK
    
    Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (MBG8FB, 0x000747C00000 Bytes = 29.12 GB)
    Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (MBG8FB, 0x000000200000 Bytes = 2.00 MB)
    
    Flashing the dead body...OK
    ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
    Resurrection complete!
    
     

    ****************Để giúp forum phát triển,anh em vui lòng share Facebook, Google+ ****************
     

Thành viên đang xem bài viết này (Thành viên: 0, Khách: 0)

X

Hỗ trợ kỹ thuât >> CHAT ngay !