Samsung N7100 - NO PRODUCT NAME REPAIR | Cộng Đồng GSM Việt Nam-Đồng Hành-Hỗ trợ-Thành Công

Trùm vật tư ép kính | Bệnh Viện Điện Thoại 24h | Linh Kiện Tín Thành | Đặt chữ quảng cáo | Đặt chữ quảng cáo | Trùm điện thoại cổ độc

Samsung N7100 - NO PRODUCT NAME REPAIR

Thảo luận trong 'ATF BOX' bắt đầu bởi jackynguyen, 5/3/14.

  1. jackynguyen

    • VIP
    Gia đình Vietnamgsm
    Làm thành viên từ: 28/6/13
    Bài viết: 60
    Cảm ơn: 100
    Điểm: 34
    M:
    Vietnamgsm GOLD:
    Hi,

    First of all repairing N7100 and I9300 eMMC is NOT A 100% SOLUTION!!!

    80% of these problematic phones NEED eMMC Chip Replacement.
    This means you only have a 20% Success Rate on whatever Box or Tools you use.
    The eMMC Firmware of Samsung VTU00M have serious FLAWS and BUGS and after analyzing the said firmware deeper, I even found that it has a self-destruct sequence. It means that the eMMC has a built-in command to KILL ITSELF!!!
    I don't know if Samsung uses this "self-destruct" command and I AM NOT ACCUSING THEM that they use this command at all. I am just saying that it is there and I have confirmed that it is the ONE OF THE REASONS why the eMMC will loose Product name in CID[103:56] (This is not Product Name in BOOTLOADER... this is eMMC Product Name Only).

    So in SUMMARY:

    1. YOU WILL NOT REPAIR ALL EMMC PROBLEMS FOR SURE.
    2. IF YOU GET 10 BAD PHONES, YOU WILL MAYBE REPAIR ONLY 2 of THEM (More than 2 if you are Lucky).3. EVEN AFTER YOU REPAIR THE EMMC, IT WILL DIE AGAIN AFTER A FEW DAYS, WEEKS, MONTHS etc...


    So without further delay, here are the Tools You need:

    1. ATF Box + Binary Repair Files for N7100
    Download Here:
    Bạn không thể xem nội dung này - Vui lòng đăng ký thành viên để được xem ! Cảm ơn.

    2. ATF eMMC Adapter (I used SmartGsm adapter)3. 2 Pieces 100 ohms resistor 1/4 watts4. Soldering Skills

    Step 1: Modify eMMC Adapter (add 100 ohms STRONG Pull-Ups)[​IMG]
    So here you will see that I added 2 resistors (100 ohms) to the CMD and the DATA0 of the eMMC Adapter. Both of the resistors act as a Strong PULL-UP to 3.3v.


    Step 2: Connect Wires to the eMMC on the PCB

    [​IMG]
    RED = CLKYELLOW = Secondary CLK (not needed if using eMMC Adapter)BLUE = CMDGREEN = DATA0PINK = 2.80v
    Now here you will notice that both VccQ and Vcc are connected to 2.8V. The actual voltages used by the N7100 is 2.8v and 2.95v respectively, so 2.8V on both power sources should do just fine.


    Step 3: Connect eMMC Adapter to ATF Box and perform "Normal Factory Erase"
    [​IMG]
    What this does depends on the actual eMMC Specs version of the eMMC. It may erase USER AREA, BOOT1, BOOT2 and RPMB or it may just erase USER AREA and nothing else.


    Step 4: Perform "Samsung Factory Format"
    [​IMG]
    What this does also depends on actual eMMC Specs version... Check out the screenshot and logs to learn more.


    Step 5: Perform "Write EXT_CSD Backup File"
    [​IMG]
    Just write back the FIRST (Oldest) EXT_CSD Backup File for your eMMC. All EXT_CSD Backups are saved here:
    C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD
    \


    Step 6: Perform "Write USER AREA"
    [​IMG]
    Just Follow Screenshot...


    Step 7: Perform "Write BOOT1"
    [​IMG]
    Just Follow Screenshot...


    Step 8: Final ChecksClick "Scan eMMC" and make sure eMMC is set to BOOT PARTITION : BOOT PARTITION 1

    You should see something like this:
    Code:
    eMMC Boot Information
    Revision 1.6 (for MMC v4.5)
    BOOT PARTITION : BOOT PARTITION 1 PARTITION ACCESS : R/W USER PARTITION
    PERM_BOOT_CFG_PROT : DISABLED
    PWR_BOOT_CFG_PROT : DISABLED
    eMMC FirmW UPDATE : DISABLED
    EMMC CACHE SIZE : 0 KB
    SUPER PAGE SIZE : 3584 KB
    HC ERASE GROUP SIZE: 512 KB
    USER AREA SIZE : 15758000128 BYTES
    BOOT PARTITION SIZE: 2048 KB
    RPMB PARTITION SIZE: 128 KB​

    Now you can de-solder the wires and assemble the Phone to check the final results of your repair.



    If you get Problems/Errors in performing steps 1 to 8, then it PROBABLY means your eMMC is one of the 80% which needs replacement!



    B.R.
     

    ****************Để giúp forum phát triển,anh em vui lòng share Facebook, Google+ ****************
    KHANH BÌNH and Taki7610™ đã cảm ơn bài viết này.
  2. Taki7610™

    • Super Moderator
    Team Unlock Vietnamgsm
    Làm thành viên từ: 27/6/13
    Bài viết: 894
    Cảm ơn: 1,264
    Điểm: 5,602
    Nghề nghiệp: KTV
    Nơi ở: TPHCM
    M:
    Vietnamgsm GOLD:
    Cái tab emmc náy chưa bắt active :D kèo thơm.
     
  3. tommyhaohoa

    • VIP
    Gia đình Vietnamgsm
    Làm thành viên từ: 28/6/13
    Bài viết: 139
    Cảm ơn: 30
    Điểm: 0
    Nghề nghiệp: mobile
    Nơi ở: 76 điện biên- tp nam định
    M:
    Vietnamgsm GOLD:
    xin hỏi anh em mình có cần chế thêm 2 con trở mặt sau chua JTAG ATF không nhỉ

    [​IMG][​IMG]
     

Thành viên đang xem bài viết này (Thành viên: 0, Khách: 0)

X

Hỗ trợ kỹ thuât >> CHAT ngay !